Scruton Marine Inc.

Marine Brokers & Consultants

Specializing in the sale of commercial marine vessels and equipment.

Head on over to the Subscribe Page  if you would like updates on New and or changes on our Listings.


Our Most Recent Featured Items

P2462

P2462 1955 47′ x 16′  Steel Pleasure Trawler For Sale Price: $38,000 CDN She’s ready for your next getaway! Draft: 2.5′ Powered by Detroit Diesel 4-71T, 200 hp Gear is Allison,

B2395

B2395 1958 43’9 x 24′ x 8′  2-Section Steel Portable Dump Scow w/ 50 Cubic Yd Capacity, Hydraulic Scissor Dump SOLD! 2 Sections  43’9 x 12′ x 8′ approx Bottoms

B2401

B2401 2000 25′ x 7′ x 3′  Foam Filled Flexi Float Barge For Sale or Rent PRICE: $8,000 USD Newly refurbished (2025) with side plating and corners Foam filled Shell plate is

P2457

P2457 1980 48′ x 13′ 6  Twin Screw Steel Cruiser/Trawler For Sale New Price: $75,000 CDN Scroll down for the YouTube video walk through! Draft: 44″ Shell plate thickness:

FV2166

FV2166 65′ x 20′  Great Lakes Commercial Fishing Vessel Price: $140,000 CDN This is not your average commercial fish tug! Click on the video below – she’s ready to be you

T2286

File No. T2286 2008 47′ x 14.6′ x 5′ Steel Model Bow Tug New Price:$250,000 CDN Built in Port Lambton, Ontario This tugboat is truckable  Gross tonnage:18.14 tons Net tonnage:13.61

LC2146

2023 30′ x 10′ Aluminum  Landing Craft For Sale Powered by Suzuki  c/w Trailer PRICE: $208,000 CDN Powered by 2023 Suzuki DF300apx w/ precision controls, less than 20 hours 39 mph top

T2406

 T2406  64′ x 18′  1100 hp Tug with Retractable Wheelhouse For Sale New Price: $55,000 USD With great lines and loads of power, she’s ready to go, go, go! Modernized in the

FV2154

File No. FV2154 1990 36′ x 9.3′ x 4.2′ Steel Trapnetter/Minnow Boat For Sale – Click on Video Below! Price: $17,500 USD Powered by Chrysler 318 Velvet drive transmission has

W2417

W2417 New 16’6 x 6′ Steel Workboat For Sale Built to order! Call for a quote today. 12 gauge bottom, 14 gauge sides 20″ transom Epoxy primed and painted Makes the perfect little

W2447

1992 23′ x 8′ Modified SeaArk Aluminum Work Boat w/Trailer (See note on engine below) New Price: $10,000 USD Note: The engine on this boat needs to be repaired – has low compression 

E2753

E2753 6 cyl Marine Perkins Diesel Engine Price: $4,000 CDN Transmission, shaft and propeller included Velvet drive transmission 110 hp Serial No 136096 Model 6.354 Prop is LH 21″ x 20″

B2400

B2400 1950’s 100′ x 30′  150 Cubic Yard Dump Scow For Sale  PRICE: $75,000 USD Estimated year of build is 1950’s Reported to be in good condition, presently in fresh  water in

G2332

G2332 Towable Kubota Diesel 15KW  120/240V Genset For Sale Price: $22,000 CDN 2001 Very clean 9,000 hours Location: near Montreal, Quebec MORE 15KW UNITS AVAILABLE – VARYING YEARS/HOURS –

M2134

560′ of 4″ Sealed PE (Polyethylene) Float Pipe For Sale Price:  $1,000 CDN (plus HST) This pipe is in very good shape Was used for floating silt control curtains Located in Southern

M2133

High Density PE (Polyethylene) Pipe For Sale Price:  $6,500 CDN (plus HST) This pipe is all in very good shape and was used occasionally for dewatering (the 4″ and 6″ pipe) as well as

B2347

 B2347 New (6) 8′ x 20′ x 4′ Sectional Barges For Sale Price: $156,000 CDN for all 6 Or – Make an offer if you’re interested in less than all 6 Shugart style barges

B2396

B2396 1984 50′ x 24′ x 4′ Sectional Barge For Sale w/Removable Material Box  PRICE: $58,000 CDN 2 Sections  50′ x 12′ x 4′ Raked at both ends Each section has 2

LC2148

2024 22′ x 8’6″  Aluminum  Landing Craft with Trailer PRICE: $109,900 CDN (plus HST) She’s got great lines, loads of room and she can really move!! LOA about

A2100

A2100  Diamond Eye Anchor For Sale  PRICE: $7,800 USD You can own a piece of Gloucester history.    This is a Diamond Eye or Banking anchor. It was pulled from Gloucester harbor decades ago. Probably

T2438

 T2438 1955 53.3′ x 15.6′  700hp Subchapter M Compliant Tugboat For Sale Price: $260,000 USD Draft is 6.4′ Air draft Mast Up: 24′, Mast down 21′ Height of eye Main

B2399

B2399 1972 180′ x 54′ x 12′ Steel Deck Barge For Sale or Monthly Lease PRICE: $990,000 CDN  GRT: 957 15 bulkheads 2 winches Last survey 2019 Reported to be in excellent

T2437

 T2437 1940/1988 74′ x 18′  500hp Steel Tugboat For Sale Price: $150,000 USD She’s got classic lines, a newer Cummins, and tons of room! Built by Gulfport Shipbuilding of Port

W2450

1970 48′ x 16′ De Vries Lentsch Twin Screw Steel Work Boat Powered by Detroit Diesel  Price: $65,000 CDN Built by the iconic W. De Vries Lentsch Jr. company of Amsterdam Draft is

W2449

1995 30′ x 9′  Steel Work Boat For Sale -Powered by Detroit Diesel  Price: $65,000 CDN This handy little workboat was refurbished in 1995 Draft is 4′ Powered by Detroit Diesel 4-71,

W2423

W2423 1995 19′ x 8’6 SeaArk Aluminum Work Boat For Sale Price: $30,000 USD She’s a small boat with a big heart and ready to get to work! 18″ draft Mercruiser 5.0 MPI, 260 hp

B2390

B2390 1965 105′ x 24′ Steel Dump Scow For Sale Call For Pricing She could use some fresh paint, but she’s ready to get to work! 350 cubic yard capacity 9’ depth from inside 9

B2394

B2394   1959 54′ x 27.5′ x 4′  3-Section Portable Steel Spud Barge For Sale NEW PRICE: $110,000 CDN for barge PRICE: $140,000 CDN for barge plus crane 2 Outer Sections are 54′

B2388

B2388 Sectional Barges, Rake Ends, Spuds, Wells and Winches for Lease or Purchase Competitively Priced Compatible with Poseidon sectionals Call for availability and pricing for: 10′ x 40′

T2428

 T2428 1946 45′ x 14′ Twin Screw Ex-Army Tug  For Sale PRICE: $40,000 USD Draft: Approx. 5′ Engines:  Detroit Diesel 6-71, keel cooled, 220 hp each Fuel capacity 900 gal Engines just

B2382

B2382 2021 27′ x 8’6 Steel Dump Barge For Sale Price: $87,000 USD Dump Box measures 12′ x 7′, capacity about 5,000 lbs Honda gas powered hydraulic power pack  90 hp Mercury

T2431

 T2431 1952 45′ x 13′ Roamer Subchapter M Compliant Model Bow Tug For Sale New Price: $169,000 USD Meet the new workhorse for your fleet! She’s ready to get to work and she’ll

W2436

 2022 21′ x 7′ Wray Brown Aluminum Work Boat For Sale w/70 hp Suzuki and Trailer New Price: $45,000 CDN Meet the next great addition to your fleet! Built by Wray Brown Welded aluminum

W2442

  1984 44′ x 12′ Twin Screw Aluminum Crew/Work Boat For Sale Price: $37,000 CDN   Powered by twin Cummins V504 MRH Borg Warner gears Fuel capacity 300 gal 3/16″ shell plate thickness

W2440

1988 22′ x 10’10” Zodiac Hurricane MK7 For Sale w/Tandem Trailer   Price: $20,000 CDN or best offer Volvo Penta 41 series diesel engine, test run late fall 2023 (runs excellent) Boat

W2437

 2021 25′ x 6’8  Steel & Aluminum Work Boat For Sale w/200 hp Evinrude and Trailer New Price: $50,000 CDN This is the one you’ve been waiting for! Steel hull with aluminum pilot

B2398

B2398 24′ x 15’7″ Portable Steel Pontoon Flat Deck Barge/ Floating Work Platform w/Spuds  PRICE: $14,500 CDN  2 Pontoons with each measuring 24′ long x 4’6 wide, x

P2460

P2460 1972 52′ x 16′ Twin Screw Hike Built Steel Cruiser/Trawler SOLD! She’s a spacious boat with great lines and requires some work to be completed. Contact us for more details

W2425

W2425 1988 28′ x 8’6 Aluminum Work/Crew Boat SOLD! Runs and drives 3′ draft Twin Mercruiser 5.7 MPI Bravo 2 outdrives Electronic shifters Dual steering stations (flybridge and cabin)

W2441

1992 28′ x 10.3′ MetalCraft Aluminum Crew/Dive/Work Boat w/Tri-Axle Aluminum Trailer SOLD! YOU JUST MISSED HER!! She’s got tons of room and is ready for work or play! GRT: 9.89, NRT:

P2456

P2456 1996 28′ x 9’6 Pursuit 2800 WA w/ Trailer SOLD! Walk around design 30′ OAL 32″ Draft Twin HE cooled Crusader 350XL low hours, just over 400 light hours Hurth

M2131

Retired 5′ Steel Mooring Ball Price:  $1,800 USD   This is an old,  retired, steel mooring ball.   It spent its life bobbing on the timeless waves of the  Chesapeake Bay. Now, it’s ready

W2448

2021 48′ x13′  Truckable Steel Work Boat For Sale – Powered by Volvo  Price: $195,000 CDN She’s got great lines, loads of room, and she’s ready to get to work! Truckable

P2455

P2455 2023 45′ x 11.5′ Steel Pleasure Trawler New Price: $75,000 CDN She’s got great lines and loads of room! 4′ Draft Powered by Caterpillar 3406B, 350hp, completely rebuilt

E2780

E2780 6-71 Natural Detroit Diesel Marine Engines (3 Available) Price:$Make Us An Offer! Running Take Outs 1 does not have a gear 2 come with Allison gears Low hours Located in New York State Details

EG2283

EG2283 Twin Disc MG509 3:1  Marine Gear Price: $11,550 CDN Good runner Located in Southern Ontario Details are deemed to be correct but are not guaranteed and should be independently verified.

PR2229

PR2229 LH & RH, 22″ x 22″, Michigan Dyna Quad, Bronze Props, 1 3/8″ Bore Price: $Call 1 in perfect shape, the other needs touching up (2 blades are slightly curled from dropping

E2779

E2779 8-71 TI Detroit Diesel Marine Engines with Twin Disc 514 2:1 Gears (2 Available) Price:$Make Us An Offer! Running Take Outs from 55′ Landing Craft Low hours Located in New York State

M2126

Solid Brass Portholes Price:  $1,000 CDN each Solid brass (she’s heavy!) Outside measurements: 18.5″ x 24.5″ x 3.5″ Glass measures 19.5″ x 13.5″ Location: Port

B2374

B2374   1990 85′ x 37′ x 5′ Landing Barge For Sale New Price: $199,000 CDN Length incl ramps 133′ GRT: 87, Net: 26 Voyage class: sheltered waters Capacity: 12 cars 52

M2129

2010 Hi-Tide Boatlift 80,000 lb Capacity Price:  $45,000 USD Fully dismantled Owner purchased a larger vessel in 2012 Has been kept in indoor storage Located in Southern Ontario  Details are deemed to

H2020

H2020 1913 106′ x 21′ Historic Houseboat Call for Pricing Large Historic 106 ft. Houseboat for Sale This is an old houseboat, located in the 1000 Islands region. It was built in the era of

PV2278

PV2278 1989 66′ x 20′ Steel 100 Passenger Boat Built by Kanter Yachts New Price: $450,000 CDN Draft 4’6″ GRT: 124.49 Net: 75 Class: Inland Waters Class II 100 passengers + 15

FE2048

FE2048 24″ Kennedy Net Lifter SOLD! YOU JUST MISSED IT!! Location: Northern Ontario  Details are deemed to be correct but are not guaranteed and should be independently verified. Please

P2444

P2444 2003 57′ x 18′ x 6.5′ Steel Custom Built Trawler/Liveaboard   Gross tonnage: 53.08 tons Net tonnage: 39.81 tons Shell plate thickness: 1/4″ Framing: 2″ x 3/8″ Bulkheads: 4 – 3/16″ plate

PR2228

PR2228 RH, 26.5″ Diameter x 16″ Pitch, 5-Blade, Bronze, Unused Prop Price: $6,500 CDN Location:  Manitoulin Island, Ontario Details are deemed to be correct but not guaranteed and should

P2461

P2461 1947 20′ x 6’7″ Classic Chris Craft Custom Runabout c/w Trailer Price: $72,500 CDN She’s a head turner in show room condition, all original and only 6 hours on the

E2778

E2778 Pair of Perkins Perama M35 Marine Engines w/Gears Price:$4k CDN each or $7k CDN for the pair GRTO from 40 trawler These engines come with gearboxes, wire harnesses, hour meters and gauges

D2139

D2139 2023 10″ Horizontal Auger Dredge For Sale Price: $185,000 CDN New hydraulic pump Completely rebuilt engine 5.9 Cummins Completely rebuilt dredging pump 10″ Stainless steel pontoons

B2387

B2387 1956 220′ x 43′ x 14′ Barge For Sale Price: $310,000 CDN Max cargo capacity about 4,000 tonnes GRT: 883 Location: Quebec, Canada Details are deemed to be correct but are not

T2435

 T2435 1957 42′ x 12’6  Mathieson Built Tug For Sale – Powered by CAT   Price: $160,000 CDN Built by Mathieson Welding Service, Goderich, Ontario GRT: 10, NRT:6.8 Draft is

T2434

 T2434 1951 42′ x 13′ Mathieson Built Tug For Sale – Powered by CAT   Price: $160,000 CDN You just found the next work horse for your fleet! Built by Mathieson Welding Service,

T2433

 T2433 1965 34.8′ x 13.3′ Steel Push Tug Powered by Caterpillar  SOLD! WHY DID YOU WAIT SO LONG??? GRT: 19, NRT:13 Molded depth: 5.1′ Powered by Caterpillar D333 (1963) Gear is CAT

M2128

17th Century Ship Cannon Price:  $30,000 USD We have a true unicorn here.   This is a 4 pound, iron long gun that spent centuries at the bottom of the sea, and was recovered intact.   It measures

P2451

P2451   2002  39′ x 13′ Steel Pleasure Tug SOLD! You missed the boat! She’s off to a new home!! Draft is 4.5′ Powered by Detroit Diesel 6-71 Gear is MG 509 2.48:1 Cruising

E2777

E2777 Cummins 5.9 6BT Turbo Marine Engines LH & RH Price: $50,000  CDN for the pair Completely rebuilt, 1/2 hour test time 1 has hydraulic steering pump and tank Both equipped with rebuilt 12V

CR2100

CR2100 Dragline Fairlead Price: $4,000 USD Can easily be adapted to marine use 20″ diameter sheaves, grooved for 1.5″ wire 2 rollers are 24″ x 5″ 2 top and bottom rollers are

E2776

E2776 Detroit Diesel 8V 92 Natural Marine Engines LH & RH Price: $7,500 CDN each Good runners Removed from a buoy tender Pay & Brinck gears, model PB130, ratio is 3:1 Located in:  Port Dover,

WANTED

Here are some of the things our clients are looking for.  If you have surplus inventory or assets you no longer use, why not let us find them a new home! Head on over to the Subscribe Page  if you

G2331

G2331 CAT 3508 Marine Genset (Needs a camshaft) Price: $25,000 CDN or best offer 3 phase 600 v 1800 RPM Needs a camshaft Location: Near Hamilton, Ontario Details are deemed to be correct but are not

EP2039

12-71 or 12-92 Tanks and Raw Water Pump w/Extra Impellers Price: $6,000 CDN for the lot One tank is set up for keel cooling The other has a heat exchanger core in it One rebuilt Jabsco raw water pump

EP2038

(2) New Jabsco Water Pump Impellers Price: $600 CDN for the pair (compare at $500 USD each!) Jabsco part number 2999-0001 Location: Port Dover, Ontario Please contact us for further information  

E2774

E2774 Caterpillar 3408B Industrial Engine New Price: $15,500 CDN Or Best Offer 402 hp Excellent running takeout Removed from a barge 1438 hours Has hydraulic governor Serial No 67U15138 402 hp Run Dec

WH2110

WH2110 Timberland 5 Drum Mechanical Winch Price: $15,000 CDN or best offer Model 400-7-252-TR Centre drum has a dog D 311 CAT power with a funk reversing drive Electric frictions Located in Port

PV2280

PV2280 1982 78′ x 23′ – 95 Passenger  Steel Tour Boat Available September 1, 2024 Price: $840,000 CDN GRT: 140, NRT: 87 Draft 5′ Cruises at 7 -1 0 knots Powered by (2) Series

P2453

P2453 1986 55′ x 13.8′ x 4.8′ Steel Trawler/Liveaboard  ***SOLD!*** Ready to see more?  Click HERE for a virtual tour of your next home away from home! Formerly a Transport Canada

EG2282

EG2282 Twin Disc MG509 3:1 Price: $20,000 CDN Good runner Removed from Volvo Penta MD 100 BK Belleville, Ontario Details are deemed to be correct but are not guaranteed and should be independently

EG2281

EG2281 Twin Disc MG509 2:1 Price: $8,500 USD Good runner Low hours Recent rebuild Very clean inside Nice gears Off of a Detroit Diesel 6-71N Windsor, Ontario Details are deemed to be correct but are

B2381

B2381 1948 (4) 10′ x 7′ x 50′ Sectional Barges  SOLD! Shell plate thickness 3/8″ GRT: 26 Good condition Winch is American 50 B, powered by a Wisconsin V4 gas engine

PV2206

FileNo. PV2206 1997 57′ x 16’9 Steel Fishing Charter Boat – Overnight Accommodations New Price: $350,000 CDN Gross tonnage: 62 tons Net tonnage: 47 tons Builder: Wray Brown

EP2037

Walter Keel Coolers  – 2 sizes available 3 are from 6-71 Detroit Diesels    $3,500 USD each 2 are from 12-71 Detroit Diesels $5,000 USD each Location: New York State Please

B2383

B2383 2018 50′ x 12′ x 5′  Steel Barge w/ Ramp and Spuds SOLD! Shell plate thickness 1/4″ Capacity approx 70,000 lbs 2 ramps 12′ x 2′ 4 spuds 2 bulkheads – 3

G2330

G2330 750 kW Kohler Genset w/16v92 Detroit Diesel Price: $8,500 CDN 3 phase 480 v Newer Panelsource control panel Powered with a 2008 model Detroit Diesel 16v92 powerplant Low hours, good runner but

SB2049

SB2049 1986 Peregrine 30 Racer/Cruiser Sailboat w/Trailer SOLD! Though her completion was cut short, this beauty is so close to being ready to go! Some elbow grease and your vision to customize the

FV2163

FV2163 1982 36′ x 10′ Steel Trapnetter/Workboat SOLD! Draft 2′ Gross Tons: 8.14 Powered by 135 hp Perkins Diesel (2015) Cruises at 6 knots Fuel capacity: 400 litres Electronics:

E2770

E2770 2 Detroit Diesel 12-71 Marine Diesel Engines SOLD! Good running take outs ready for your latest re-powering job! Keel cooled Fleet maintained in a state run ferry Located in:  New York State

G2329

G2329 Detroit Diesel 8-92 Marine Genset Price: $30,000 USD 700 hours Supercharged and Turbocharged Demand start 330 kw 480V 3 phase 60 hz Was a standby generator Good runner Has heat exchanger

EP2036

Fernstrum Keel Coolers – New – 2 sizes available Model D1672 Price $13,000 CDN Model BN842B Price $4,000 CDN Location: Near Port Dover, Ontario Please contact us for further

M2127

Solid Red Brass Portholes Price:  $3,500 CDN each Gorgeous rare red brass porthole (she’s heavy!) Outside diameter 20.5″ x 3.5″ Solid yellow brass dogs Location: Port Dover,

FV2157

FV2157  71′ x 18.5′ x 6′ Great Lakes Commercial Fishing Vessel Price: $65,000 CDN Powered by Volvo 120A ( 270 to 290 hp) Capital Gear 3.88:1 ratio 44” x 40” 4 blade RH propeller 3 ½”

W2430

 1960 50′ x 15.5′ x 5.5′ Steel Double Bottom Work/Cargo Tug  Built by Hike Metals, Wheatley, Ontario SOLD Last survey 2019 Gross tonnage: 17.24 tons Net tonnage: 11.74 tons

G2327

G2327 Westerbeke 4.4 kw Diesel Marine Genset Price: $3,500 USD Complete less panel 450 hours Mounts, strainer, Racor, etc Location: Windsor, Ontario Details are deemed to be correct but are not

EG2280

EG2280 Twin Disc MG509 1.45:1 Price: $3,500 CDN Should be overhauled Port Dover, Ontario Details are deemed to be correct but are not guaranteed and should be independently verified.  marine gear for

A2096

A2096 30 kg New Danforth Anchors  Price: $75 CDN each Galvanized steel Located in Port Dover, Ontario Details are deemed to be correct but are not guaranteed and should be independently verified.

E2756

E2756 Detroit Diesel 16-71T Engine Price: $4,000 CDN Good running take out Removed from a generator 1550 original hours Located in:  Port Dover, Ontario Details are deemed to be correct but are

D2120

D2120 Mudcat MC915 Auger Dredge For Sale Price: $132,500 CDN Construction material – Steel Length : 38’ 11″ Width : 9′ 0″ Height : O.A.8’8′ Weight : 21,000 lbs.

FV2157

FV2157  71′ x 18.5′ x 6′ Great Lakes Commercial Fishing Vessel Price: $65,000 CDN Powered by Volvo 120A ( 270 to 290 hp) Capital Gear 3.88:1 ratio 44” x 40” 4 blade RH propeller 3 ½”

G2326

G2326 Stamford/Detroit Diesel 600 V Genset Price: $5,500 CDN 151 Amp,  600V, 3 phase 1823 hours Used as a standby genset Government maintained Skid mounted 12 wire alternator end Copper windings

M2125

Bronze Kerfort Marine Windows Price:  Make an Offer! (2) 20″ x 27″ 1/2 opening (1) 25″ x 30″ fixed (non-opening) (3) 25″ x 30″ fully opening Location: New York

W2428

W2428 1982 41′ x 14′  Twin Screw Aluminum UTB/ Workboat/Pilot Boat For Sale Price: $130,000 CDN She’s got nice lines and loads of space! GRT: 14.99 Former Coast Guard and Toronto

P2454

P2454 1983 30′ x 9′ Welded Steel Motor Boat Project Boat Price: $9,500 CDN or Best Offer This project boat has nice lines and loads of potential! 3′ Draft Built by Kettle Creek Boat

B2354

 B2354 2018  180′ x 12′ Floating Bridge or 2 Barges with Ramps For Sale  Price: $139,000 USD These custom units were designed as a bridge but could be used as 2 separate barges 2 Barges

B2380

B2380 2022 10′ x 27′ Aluminum Crane Barge w/Trailer  SOLD! This nearly new beauty that makes moving boat lifts and docks a breeze! Draft approx 1′ Plate thickness: deck is

PR2227

PR2227 RH, 30″ x 25″, 2 1/2″ Bore, 3-Bladed, Kennedy Work Prop Price: $950 CDN Needs clean up Removed from a 38′ Russel Brothers tug Location:  Windsor, Ontario Pickup only

W2422

W2422 1989 34′ x 10’5 Aluminum SeaArk Crew/Work/Dive Boat SOLD! YOU JUST MISSED IT!! 3′ draft Potential to be a great dive boat with stbd dive door and aft dive platform Twin Cummins

P2448

P2448 1957 40′ x 12′ Matheson Trawler Tug SOLD! YOU JUST MISSED IT!! Draft is 4.75′ Converted dive boat, now a live aboard Steel hull 1/4″, house is 3/16″ aluminum

W2370

W2370 1980 26′ x 10.5′ Twin Screw Aluminum Work Boat For Sale Price: $25,000 CDN GRT: 7.68, NRT: 5.76 Draft: 3.3′ Powered by Volvo Penta Turbo Twin D3-160 A EVC-B, 2005, 160 hp, 320

PV2276

PV2276 1986 90′ x 24′ – 250 Passenger Twin Deck Tour/Charter Vessel New Price: $995,000 CDN Last drydock 2023 90’4″ x 24′ GRT: 269, NRT: 230 Ideal for private and

WH2117

WH2117 Ingersoll-Rand Air Tugger SOLD! Serial #18786 Size HU Located near Chicago, Illinois    Details are deemed to be correct but are not guaranteed and should be independently verified.

WH2119

WH2119 (2) Nabrico 40 Ton Makeup Winches SOLD! YOU JUST MISSED THEM! Left and Right hand units Dogging tonnage is 40 tons Condition: solid steel units, turn freely Located in New York State    Details

W2387

W2387 1985 21′ x 8′ Aluminum Work Boat w/ Trailer SOLD! YOU JUST MISSED IT!! Draft 32″ Shell plate thickness: 1/4″ bottom, 3/16″ sides and deck and pilothouse ***Requires

E2772

E2772 Detroit Diesel 6-71 T Engine Price: $2,500 USD Right hand Good runner Bypass blower SAE #1 bell housing Located in:  New York State Details are deemed to be correct but are not guaranteed and

E2720

File No.E2720 2006 CAT Marine Diesel Engines – C12 Engines (2) 340 hp @ 1800 rpm New Engines with 28 hours on them Set up for keel cooling Price: $30,000 USD Each Located in New York State

CR2098

CR2098 Appleton Marine Crane Price: $10,000 USD Model KEB50-35 10,000 lbs at 35′ 20,000 lbs at 25′ 30,000 lbs at 17′ Crane weighs approx 35,000 lbs Good condition Needs hydraulic

WH2118

WH2118 Ingersoll Rand Air Tugger BU 7A Price: $4,000 USD 1000-pound capacity Like new, tags are still on it! Located in New York State    Details are deemed to be correct but are not guaranteed and

CR2097

CR2097 Esco CS1422 Clamshell Bucket Price: $2,500 USD Bushings and sheaves are in good mechanical shape and are free to roll Located in New York State Details are deemed to be correct but are not

CH2014

CH2014 NEW DATREX 30″ LIFE RINGS Call for price –  Volume Discount Available Model DX0325D Polyurethane Foam Buoyant Material Fluorescent reflective strips White grab lines Weight 2.5 kg

CH2013

CH2013 NEW TAYLOR MADE MARKER BUOYS Price: $200 CDN EACH 2 green available, 1 red 49″ high, 10″ wide at top, 18″ at the widest part Sits 39″ above waterline Tough UV protected

EG2279

EG2279 ZF IRM301 1:1 GEAR Price: $1,600 CDN Suitable for a pleasure craft Made in Italy 2005 No drive ring available Southern Ontario Details are deemed to be correct but are not guaranteed and should

PV2227

File No. PV2227 1984 78′ x 26′ x 4′ New Orleans Style Stern Wheeler       Presently not available – She’s in drydock getting a facelift! Built by Freeport Shipbuilding

P2445

P2445 2012 31′ x 10′ Custom Steel Trawler w/Trailer SOLD! YOU JUST MISSED IT! Draft 3’9 31′ plus bow pulpit and swim platform Hull is 10 ga construction, cabins 12 ga Powered

W2421

W2421 2022 33′ x 12′ New Build Heavy Aluminum Work Boats and Landing Barges CALL FOR CURRENT PRICING Built BY marine contractors FOR marine contractors! Transport Canada licensed Team of 6

B2376

B2376 New Sectional Barges, Heavily Framed, Built to Last! Price: CALL FOR PRICING Built to order sectional barges Built BY marine contractors FOR marine contractors! 48 Years experience working on

M2123

Steel Boat Lift Price:  $2,500 CDN or Best Offer Hydraulic lifting gear is powered by Honda 4-cycle engine Includes steel walkway as shown in photos Sold as is, where is (i.e. you disassemble)

P2447

P2447 2019 30′ x 10′ Steel Pleasure Tug w/Trailer SOLD! YOU JUST MISSED IT! Draft is 3.5′ at stern Shell plate thickness: 11 gauge Headroom: 6’2 Cruises at 7 mph, top speed 9

M2115

M2115 Yard Dolly/Transporter New Price:  $3,900 CDN Excellent condition, freshwater use only Ex-USCG Suitable for boats up to 46′ Location: Greater Toronto Area, Ontario  Details are deemed to

W2420

W2420 2022 21′ x 6’8″ Aluminum Work Boat Price: $15,800 CDN 5′ bottom 3/16″ welded aluminum hull Located near Port Dover, Ontario Details are deemed to be correct but are

FV2156

FV2156 1945/1986  65′ x 20′ x 5′ Great Lakes Commercial Fishing Vessel SOLD! Details are deemed to be correct but are not guaranteed and should be individually verified Please

FE2045

FE2045 30″ Crossley Net Lifter w/Roller and Pan SOLD! Totally rebuilt recently, jaws, springs, etc Aluminum top Includes hydraulic pump attached to lifter Used only in fresh water (Lake

A2090

A2090 Large Folding Stock Anchor Price: SOLD! YOU JUST MISSED IT! 6′ across the flukes, shank is 9′ long Weight approx. 1,600 lbs Location: Maryland This is a large folding stock anchor.

A2094

A2094 Baldt 29 Stockless Anchor w/ Chain Price: $7,000 CDN 6′ tall, 4′ wide Weighs roughly 4,000 lbs 9 chain links 10″ long, 1 7/16″ diameter; 1 swivel; 1 D-ring Chain is

CR2096

CR2096 Kinshofer Model 632 Hydraulic Grapple Price: $5,000 USD Ser# 9708265, Model 632-2 Timber or railroad grapple Weight 290 kg Capacity 0.75 m² Max working pressure 200 bar Excellent condition

B2368

 B2368 Flexifloat Barges – For Lease Only at This Time Price: 40′ x 10′ x 5′ (2 available) Price: 20′ x 10′ x 5′  (5 available) Last survey 2021

CR2095

CR2095 2013 40 Ton Container Crane and Runway Price: On Request Made by Advanced Crane Technologies Bridge/Trolley Speed: 130 FPM Bridge Travel: 100′ Trolley Travel: 50′ Lift: 30′

WH2102

File No.WH2102 Markey Single Drum Towing Winch Price: SOLD! Model TDS-32 Wire Size: 2″ Drum Capacity: 2100′ Style: Single Drum Line Pull: 120,000 Diesel driven – Detroit Diesel with

M2118

M2118 Crown Order Picker New Price:  $4,500 CDN Model 30SP42TT Serial No 1A1475954 Hours 198.3 Capacity: 3000 lbs Comes with battery charger – Exide, Model 666 Plus Location: Newfoundland

EG2274

EG2274 Twin Disc Marine Gear – MG 5091 3.83:1 Price: $11,500 CDN #1 Housing Expertly rebuilt Located in New Brunswick, Canada Details are deemed to be correct but are not guaranteed and should

EG2273

EG2273 Twin Disc Marine Gear – MG 509 4.5:1 Price: $12,500 CDN #1 Housing Expertly rebuilt Located in New Brunswick, Canada Details are deemed to be correct but are not guaranteed and should be

M2119

MI 30 Oil Recovery Skimmer New Price:  $3,500 CDN Make Morris Model MI-30 Power pack- Yanmar diesel 320 pounds Location: East Coast of Canada  Details are deemed to be correct but are not

PR2211

PR2211 RH  32″ x 32″, 3 Blade Michigan Propeller, 2.5″ Bore Price: $1,500 CDN Needs a bit of work Location:  Southern Ontario Details are deemed to be correct but not guaranteed and

PR2209

PR2209 RH  38″ x 32″, 4 Blade, Michigan Workhorse Propeller, 3.5″ Bore Price: $7,500 CDN Good used condition Location:  Southern Ontario Details are deemed to be correct but not

EG2267

EG2267 Tonanco Marine Gear, TM828 S, 3:1 New Price: $10,000 CDN Serial No 1350 G Running take out Filter clean and good pressure Spin tested Oil leak on input shaft Equivalent to Twin Disc MG-514

M2122

Bow Thruster Price:  $2,000 CDN Bow thruster has a 3 bladed fixed pitch propeller 9 ¾’’ x 24 FPP Prop is in a good condition. No dents, no mechanical damage, no cracks, no visible damage, etc.

M2121

Marker Buoy 6′ Diameter – 4 Available Price:  $2,500 USD Heavy, durable construction Good condition Letter can be removed or changed Location: New York State  Details are deemed to be

M2120

Used Heavy Duty D-Rubber Price:  $500 USD per length – Quantity Discounts Available Up to 11′ lengths 70 lbs per ft Location: New York State  Details are deemed to be correct but are not

G2317

G2317 Hydraulic Generator – Mounts on Top of 514 or 5114 gears 12.5 KW Price: $10,000 CDN  Located in Southern Ontario Details are deemed to be correct but are not guaranteed and should be

M2117

M2117 2016 18′ x 5′ Dock Price:  $6,800 CDN 3′ high Wood over steel frame Never in water – used as model for home show 4 foam billets for floats Location: Eastern Ontario

A2091

A2091 Russel Bros Ltd. Anchor “Fort Frances” “450 LBS” Price: $6,000 CDN Reads “Russel Bros Ltd Fort Frances” and “450 LBS” and “L5” Stock

WH2114

WH2114 (2) Timberland 10,000 kg Hand Winches Price: $Reasonable offers will be considered Max line pull 10,000 kg Ser No: 78-12886 Drum size approx: 12″ long x 7″ diam Each winch weighs 1

PR2206

PR2206 RH/LH  66″ x 68″, 4 Blade, Coolidge, Stainless Props, 6.5″ Bore Price: $5,000 USD each Weigh approx 3,000 lb each Usable, a couple tips might need a little TLC Removed from a

CR2093

CR2093 1999 Grove RT860 Price: $95,000 USD 5100 hours 60 ton capacity Good condition Two drums 115′ main boom 30′-60′ jib Ready to work Located in New York State Details are deemed

WH2113

WH2113 Air Winch Price: $3,000 CDN 15,000 lb capacity Located in Quebec    Details are deemed to be correct but are not guaranteed and should be independently verified. Please contact us for further

WH2019

WH2019  Joy Air Tugger Winch 5000 lb pull 30hp Model B2F-211 Located in Quebec Price $5,250 CDN Details are deemed to be correct but are not guaranteed and should be independently verified.

G2313

G2313 Cummins/Onan Genset 30KW, 600V Price: $8,000 CDN  c/w muffler Located in Quebec Details are deemed to be correct but are not guaranteed and should be independently verified.  Used Generator for

D2138

D2138 2010 Suction Dredge For Sale Price: $147,000 CDN Width: 8’6 Length: 26, Cutter Head 18′ Draft: 20″ 8″ Suction, 6″ Discharge Both sides can discharge or can be

B2361

 B2361 SECTIONAL BARGES FOR LEASE  Price: $Depends on Use and Duration, call for pricing 2009 – 2017 Poseidon and Flexi Float 10′ x 40′ x 5′  and 10′ x

T2410

T2410 1939 98’7 x 22′ x 9′ 1200 hp Tug For Sale Price: $250,000 USD GRT: 132, NRT 49 Built in Port Arthur, Texas by Gulfport Boiler & Welding Powered by EMD 12-567, 1200 hp, 5

S2044

S2044 1980 62’6″ x 19’8″  Steel Ex CCG Buoy Tender For Sale  Built by Canadian Dredge & Dock Co., Kingston, Ontario Class Voyage: Inland Waters II Taken out of service in

CR2092

CR2092 Case CX240 LR Long Reach Excavator Price: $125,000 CDN 2600 hours w/ all new Trimble Instrumentation for a GPS system Located in Belleville, Ontario Details are deemed to be correct but are not

SP2226

File No.SP2226 Set of D2 Brass  Kahlenberg Horns Price: $1,100 USD Removed from a NY commercial fishing vessel 20+ years old  Located in NY State Details are deemed to be correct but are not

D2119

D2119  2011 Mudcat MC-910 Aluminum ENV Suction Dredge For Sale Principal Dimensions and Characteristics Custom Built in 2011 Length Over All: 11.62 m 38.11 feet Width: 2.74 m 9 feet Height Over All:

W2386

W2386 2011 26.48m x 11m Multicat Eurocarrier 2611 Price: Call for Pricing Draft 2.8 m (tanks 98% full) Deck space 125 metres², Deck load 6 tonne/sq metre Class: MCA Cat 1 150 miles from safe haven

M2111

File No.M2111 Locking Cast Aluminum Deck Plate – New – Lunenburg Foundries Price:  $900 CDN Mounting ring O.D. 30″ , I.D. 26″ New, never installed With stainless locking lugs

PV2268

File  No.  PV2268 1977  50′ x 15′  Aluminum Passenger Tour/Dinner Boat Price $325,000 CDN Last COI (2024) is for 51 passengers and crew Capacity could be increased with modifications Built

G2296

File No. G2296   Perkins Diesel Generator 100KW Price: Call 519-583-1636 or email sms@scrutonmarine.com This Perkins diesel generator is suitable for continuous use and has plenty of power for

Email:  sms@scrutonmarine.com 49 John Street, Port Dover, Ontario, N0A 1N7